PDF Instructions

 Security Cable Instructions

 Troubleshooting Guide

Watch Video Instructions

Opening the Safe for the First Time:

• Take the Included keys (located in a cutout in the foam packaging)
• Insert Key into Keyhole & Turn Right (clockwise) to open the door

Adding Power to the Safe Using Battery or Power Cable:

WHY THIS BATTERYBecause this battery has the highest amperage output that is needed to operate the lock.

• Locate the battery compartment inside the safe
• Pinch together the tabs on the battery tray and slide it out
• Correctly insert a Duracell Coppertop 9-Volt battery into the tray and slide tray back into compartment [lock will chime]

• Alternatively, you can simply plug in the included power cord into the port located on the left side of the safe
• Yes, you can have both the battery installed and the power cord plugged in at the same time

Setting your 6-Digit Combination

NOTE: When you first receive the safe the electronic keypad is set to the factory default of 1-2-3-4-1-2

• STEP 1: Hold down BUTTON 1 until green light turns on – lock will beep twice
• Button 1 is the first button on the far left of the keypad
• STEP 2: Enter the current 6-digit code - Lock will beep twice
• Factory Default Code 1-2-3-4-1-2
• STEP 3:Enter your NEW 6-digit code – lock will beep three times
• STEP 4: Re-enter your NEW 6-digit code – lock will chime
• Your new combination has been successfully set!

Error Note:If lock beeps 5 times, the combination was not installed successfully. Simply restart from STEP 1.

IMPORTANT! Test your new code several times with the door open to ensure the new code is properly set up before closing and locking the safe so you don’t get locked out.

Registering a Fingerprint

IMPORTANT: This safe will open on any fingerprint until the first fingerprint has been successfully registered. Make sure you at least register 1 fingerprint before storing valuables inside. This safe can store up to 31 different fingerprints. If you think you have registered your first fingerprint and it still opens on any fingerprint then you did not properly register that fingerprint and should try again.

• Press ONCE [DO NOT HOLD] the Biometric Scanner Button – lock will beep twice and biometric scanner will illuminate green
• The Biometric Scanner Button is located inside the safe near the battery compartment and the interior light
• Place and hold your finger fully on biometric scanner – hold your finger in position until lock chimes
• Chime indicates your finger was successfully registered!

Error Note:If lock beeps 5 times, that fingerprint was not installed successfully. Simply restart from the beginning of registering your fingerprint.

Silent Mode

To turn ON Silent Mode press and hold Button 4 for about 5 Seconds until you see a light flash. To turn OFF Silent Mode Hold Button 4 again until light flashes and you hear a beep.

Resetting your SwiftVault

• Hold down biometric scanner button until lock beeps 5 times
• Lock will reset to the factory default code of 1-2-3-4-1-2 , erase all registered fingerprints and open on any fingerprint until one is successfully registered.

TROUBLESHOOTING

• LOCKOUT MODE: If the safe is constantly beeping, won’t let you enter your code on the electronic keypad or use a registered fingerprint to get into the safe, your safe is in LOCKOUT MODE. This is a built in safety feature that happens with 4 consecutive wrong entry attempts. Wait 5 minutes for beeping/flashing to stop [with power added to the safe]. Retry your fingerprint/code or reset your safe back to default settings by holding down the registration button.
• Please Note: Power must be added to the safe during the whole 5 minute lockout period via either the installed battery or power cord. Removing the power will only pause the 5 minute timer, only to be resumed once power is added back to the safe.
• LOW BATTERY: if buttons can be pressed, scans fingerprint and clicks to unlock but the safe door doesn't open, short red flash after entry attempt on keypad or scanner. This means the battery you have installed in the safe is low and doesn’t have enough power to open the door of the safe. You will need to open the safe with the override key or plug in the power cable and enter your code. Then replace the battery with a brand new Duracell Coppertop 9V Battery.