Doomsday EMP proof Rotobolt High Security Safe Lock by LP

The most secure lock on the market today.

Easily add some extra protection to your already highly secure safe.


The Premier Redundant RotoBolt Lock and Keypad is a manipulation-resistant 4-wheel Combination Lock with an Electronic Lock override. It can also be used as an Electronic RotoBolt with a mechanical combination lock override. The lock has a standard mechanical lock footprint.

Mounting the lock is quick and easy and requires no spline key. It's used with a square shaft as the spindle. With its unique design, there is not need to remove the back cover for installation.
  • Redundant RotoBolt with Bright Chrome Keypad
  • EMP proof
  • Redundancy to play it safe
  • Premier redundant rotobolt lock
  • Audible and visual feedback
  • Durable mylar keypad
  • Spy-proof Digital Entry (top reading)
  • Sliding door access to battery compartment

SPECIFICATIONS


Part Number: RR40-20-K

ELECTRONIC LOCK

  • Type 1 Electronics
  • Patented Simple Software (1 Manager / 1 User)
  • 6 Digit Changeable Code
  • Simple Code Change
  • Function #5 Self-Diagnostics
  • Low Battery Warning
  • Manipulation Protection

MECHANICAL LOCK

  • Group 2M Mechanical
  • Manipulation Resistant
  • Standard Foot Print
  • No Spline Key Required

ELECTRONIC LOCK OPERATING INSTRUCTIONS

  • Operates with a six-digit code
  • After entry of a valid code, a double beep with follow
  • An invalid entry is followed by a long signal
  • After 10 seconds without entry, the current code being entered will be voided
  • Locks are set-up by the safe manufacturer and set to the default code of: 1-2-3-4-5-6

CHANGE USER CODE

  1. OPEN SAFE USING THE CURRENT CODE (Default: 1-2-3-4-5-6) - KEEP DOOR OPEN THROUGHOUT PROCESS
  2. Press and Hold [0] until you hear a double beep
  3. Enter existing user code (Default code is: 1-2-3-4-5-6) - You will hear a double beep
  4. Enter new code - You will hear a double beep
  5. Reenter new code - You will hear a double beep
  6. Your new user code is now installed
  7. Test new code with the door of the safe still open
  8. If you hear a long beep while trying to change the code, the lock has timed out and your new code has not been registered
  9. Reopen safe with the preexisting code and then retry

BATTERY INFORMATION

  • The battery compartment is located at the bottom of the lock.
  • The battery must be connected to the battery connector found inside the battery compartment
  • Use only 9V ALKALINE batteries
  • Duracell or Energizer batteries are recommended
  • A series of signals after code entry indicates that the battery is weak and needs to be replaced

LOCKOUT MODE

  • After four-consecutive invalid code attempts, the keypad will enter lockout mode for 5 minutes
  • During the lockout period,the LED light will flash every 10 seconds and any key pressed will cause a long beep
  • Lock will continue to reenter lockout mode after every two consecutive invalid code attempts until the correct code is entered

COMBINATION LOCK OPERATING INSTRUCTIONS

  • Always turn the dial slowly and carefully
  • Up the Opening Index to OPEN
  • On the last turn for each number, stop exactly when the number is in line with the Opening Index. In case you turned too far, you cannot correct this by turning back.
  • In case of error, start over beginning with the first number

OPENING YOUR SAFE USING THE COMBINATION LOCK

  1. Factory combination is "50"
  2. Please refer to your safe owners manual for your unique combination and carefully follow the instructions to open using the dial in the center of your lock
  3. Turn dial RIGHT (clockwise), pass the first number in your combination FOUR times and stop on the FIFTH time, when the number line is fully lined up with the OPENING INDEX
  4. Turn dial LEFT (counter-clockwise), pass the second number in your combination THREE times and stop on the FOURTH time, when the number line is fully lined up with the OPENING INDEX
  5. Turn dial RIGHT (clockwise), pass the third number in your combination TWO times and stop on the THIRD time, when the number line is fully lined up with the OPENING INDEX
  6. Turn dial LEFT (counter-clockwise), pass the fourth number in your combination ONE time and stop on the SECOND time, when the number line is fully lined up with the OPENING INDEX
  7. AFTER YOUR NEW COMBINATION HAS BEEN DIALED INK TURN THE DIAL TO THE RIGHT AND STOP ON [0] AND TURN THE HANDLE OF YOUR SAFE TO OPEN (UNLOCK)
  8. TO LOCK THE SAFE, CLOSE THE DOOR, ROTATE HANDLE TO LOCKED POSITION AND ROTATE DIAL 3 TURNS IN EITHER DIRECTION

TIPS TO ASSURE THE HIGHEST SECURITY WITH YOUR LOCK

  • NEVER select a code from personal data (birthday, telephone number, anniversary, etc)
  • Each number should be at least 4 numbers apart from each other (NOT in sequence)
  • NEVER set the last number between 0 - 20

INFORMATIONAL VIDEO


UPGRADE AVAILABLE ON THESE SAFES





QUESTIONS? LET ONE OF OUR SAFE EXPERTS HELP YOU: 800.827.7534

SHIPS SAME DAY* • SUPERIOR CUSTOMER SERVICE • 100% SATISFACTION GUARANTEED
Want to be invited to Dean Safe's private sales? Subscribe below. Rather order by phone? Need more information?
Call (800) 827-7534 and one of our safe experts can help you find the right safe to fit your needs.

All photos & words are copyrighted© 1978-2017 by Dean Safe or their respective owners. All rights reserved. Get discount prices and great deals (and often free shipping) when you order online from Dean Safe. Your purchase is protected by our 100% satisfaction guarantee and our secure servers. Review our products with our expert comparisons, reports, buyers guides and reviews. Shop our online closeouts for sale items, bargains, with values ranging from good savings to downright cheap!
*Same Day Shipping: Orders placed by 3pm (PST). Applies to most items (indicated on each product page).